This article proposes the development of a novel tool that allows real-time monitoring of the balance of a press during the stamping process. This is performed by means of a virtual sensor that, by using the tonnage information in real time, allows us to calculate the gravity centre of a virtual load that moves the slide up and down. The present development follows the philosophy shown in our previous work for the development of industrialised predictive systems, that is, the use of the information available in the system to develop IIoT tools. This philosophy is defined as I3oT (industrializable industrial Internet of Things). The tonnage data are part of a set of new criteria, called Criterion-360, used to obtain this information. This criterion stores data from a sensor each time the encoder indicates that the position of the main axis has rotated by one degree. Since the main axis turns in a complete cycle of the press, this criterion allows us to obtain information on the phases of the process and easily shows where the measured data are in the cycle. The new system allows us to detect anomalies due to imbalance or discontinuity in the stamping process by using the DBSCAN algorithm, which allows us to avoid unexpected stops and serious breakdowns. Tests were conducted to verify that our system actually detects minimal imbalances in the stamping process. Subsequently, the system was connected to normal production for one year. At the end of this work, we explain the anomalies detected as well as the conclusions of the article and future works.
Keywords: virtual sensor; DBSCAN; predictive maintenance; tonnage monitoring; I3oT
In recent years, large companies have been racing towards a full digital transformation, applying technological solutions that allow them to manage the large amount of data they obtain from their businesses. The objective is to obtain solutions that give them a great advantage in decision making and thus increase competitiveness over other companies in the same sector. A full digital transformation has been carried out [[
Focusing our attention on maintenance strategies, in recent years, a large number of proposals have been presented regarding the use of sensors and artificial intelligence for defining the state of the machine, also called smart maintenance [[
The automotive world is one of the most demanding, and one of its strengths is a high availability of machines. Many assets are used to achieve an organised production without delays and with the supply of material from controlled suppliers so that there is no error. This is why a breakdown in the manufacturing chain poses great problems, since every minute that no cars are manufactured the company experiences high economic losses. In this way, brands seek to have increasingly modern plants [[
The stamping process is one of the most complex processes throughout the car manufacturing process, where there are many opportunities for improvement with the use of technologies proposed in Industry 4.0. Industrial presses are a piece of mechanical equipment of great design complexity and large dimensions, where we find a lot of unknown information during the stamping cycle. Production stops due to breakdown can have different causes, since a press is composed of a large number of mechanical elements and a failure of these may cause the equipment to stop. The most serious faults are breaks in the kinematic eccentric transmission system and its components, such as bolts, connecting rods, bearings, gears, etc., due to their high economic impact for a company. That is why it is important to perform proper preventive maintenance. The problem is that even if appropriate maintenance is performed, the breakdowns continue to occur. Even worse, these faults can trigger a major breakdown, with the appearance of cracks in important components, such as connecting rods and eccentric dynamic driven gears, or in the structure of the press, which may incur an exorbitant cost. When these faults appear, it is chaos for the company due to the restructuring that this entails in the plant and the high cost and repair time that these types of breakdowns incur, since the factory does not usually have these types of components in stock and they need to manufacture them.
In the following Figure 1, you can see a triangular connecting rod that has broken transversely following the appearance of a crack. After analysing the transmission system, it was verified that multiple cracks had appeared along the surface of the connecting rod and that this was the consequence of an imbalance or minor fault that ended up causing a crack.
Recent research seeks to obtain new knowledge about what happens with the equipment [[
The new methods for maintenance strategies in Industry 4.0 may help decrease the time and cost associated with predictive maintenance. However, there are still challenges to overcome in predictive maintenance [[
In our previous work, we proposed a new methodology based on technologies of the fourth industrial revolution called Mini-Terms [[
The aim of the method is to predict and detect when a sub-component of the manufacturing line is going to break, such as welding guns [[
The objective of our research is to create an IIoT+Big Data tool for the stamping process using sensors installed in the press for automatic operation, following the philosophy of our previous works [[
In this article, we present a tool that allows us to monitor the balance of the press during the stamping process in real time. The creation of this tool is based on experience acquired by the employees of the factory. It is known that when the mechanical components begin to deteriorate, an imbalance is generated in the mobile part of the press. If the wear of the components is in an advanced stage, this can be identified by the human eye. In the present tool, the imbalance of the press is measured by a virtual sensor which, using the tonnage information in real time, allows a calculation of the gravity centre of a virtual load that moves the mould up and down. The aim is that the gravity centre of the virtual load works as central as possible and without bring over-stressed, thus ensuring that the wear of both the die and the mechanical elements of the press does not increase. The tool developed will be used as a watchdog, notifying us when we are working under unfavourable conditions so that we can make the relevant adjustment to the process and ensure the manufacturing process is being carried out without damage to the press or the tool used.
The article is distributed as follows. In Section 2, a brief description of the stamping process is given. In Section 3, we detail the strategy used to obtain information about the process and the form of the data. In Section 4, we explain the theoretical concept of the virtual sensor method and how to monitor the state of the press taking into account the physical sensors and their advantages. In Section 5 and Section 6, we show how the proposed algorithm has been defined for detecting abnormal working conditions and detail the obtained results. Finally, in Section 7, we show the conclusions and future work.
Two types of presses are used in sheet metal forming, mechanical (single action (SA) or double action (DA)) and hydraulic, both can be used in all operations carried out in stamping (blanking, deep drawing and trimming). The major difference between SA and DA presses is the eccentric drive transmission system and the blank holder force system. In SA presses, as seen in Figure 2, there is one slide for the tool and at the bottom of the press there is a cushion system as a blank holder. This is in contrast to DA presses that have a more complex eccentric drive system with two slide displacements, one for the blank holder and other for the punch, but without a cushion at the press base. Double effect presses have been used for years in deep drawing operations, but recently they have been replaced by hydraulic and SA presses with cushions because they are more efficient in deep drawing operations [[
A cycle of the stamping process can be separated in three phases. First is the downward motion of the slide when the electrical motor activates the kinetic movement of the press through the flywheel with a controlled speed. Second is the stamping phase, where we carry out deep drawing, trimming and bending or flanging and the material is deformed. The last phase is the upward motion where the counterbalance pressure helps the press to rise the die until the end of the cycle, waiting for the idle process to start the cycle again.
In a stamping press, we can find different components that are synchronised. The electric motor activates the movement of the press through the eccentric transmission system. The slide, where the upper die is placed, is moved up and down with a variable press speed due to the design of the eccentric drive system. The hydraulic/pneumatic clutch and brake system start and stop the sliding movement between operations. The pressure of the counterweight helps the electric motor lift the slide. The hydraulic cushion controls the amount of material introduced into the die during stamping. Each of them is composed of several subcomponents such as gears, shafts, connecting rods, pumps, etc. Due to the number of existing items that may fail, the maintenance of a press becomes an arduous task which consumes many resources of the company. Despite the effort made, unexpected breakdowns continue to occur.
The concept introduced in [[
In [[
The purpose of C-360 is to store data from a sensor each time the encoder indicates that the position of the main axis has rotated by one degree. Since the main axis makes a turn in a complete cycle of the press, this criterion allows us to obtain information from the three phases of the process and easily shows where the measured data are in the cycle measurement data. As a general rule, the degree 180 is the bottom dead centre (BDC) and the degree 320 is the top dead centre (TDC). As seen in the example of the measured data of a tonnage sensor in Figure 3, we can see the moment when the press goes up and down within the cycle. The sensors for which data are being received in the c-360 are shown in Table 1.
The time it takes for the press to run a cycle is about 3–4 s. If the speed of movement of the press is constant, a data point would be stored approximately every 10 ms. However, as we can see in Figure 4, the distance to the BDC of the slide is not linear with respect to the degree of the press position. We can see clearly that in deep drawing, the slide moves more slowly, while in the downward movement, the slide moves with a controlled speed and the highest speed can be observed in the upward movement. Using the C360 criterion implies that for scanning the data in the time domain, the storage frequency of the data varies throughout the cycle. However, when scanning the data in the position domain of the press, the data storage frequency is the same during the cycle.
In the deep drawing stage, the movement is between 150 and 200 mm depending on the die. Here, we can read between 80 and 100 data values, i.e., one every 2 mm. As a result of the fact that the speed of the press is slower here, we have more time to store the data in the PLC die so that we can ensure a higher accuracy when reading the sensor data. In addition, tests were performed to verify the capacity of the PLC and we found there was no loss of information. As seen in Figure 3, the accuracy and frequency of the data measured in the cycle are good enough to obtain the required process information.
From all the sensors available in the press, we selected the ones that will provide us with the most critical information about the process. The selected sensors are already installed in the press and are used for automatic operation afterwards; they give free information. Table 1 shows the monitored variables.
Two conditions must be met to ensure that we are performing correct manufacturing in the stamping process to prevent both excessive wear of the tool die and unfavourable deformations of the press structure. These are:
- The stamping of the press must be as centred as possible to prevent an imbalance from happening in the upper die of the press. The press is an element that becomes deformed and therefore an excessive effort or an imbalance will favour the appearance of breakdowns and will increase the wear of the different mechanical elements of the equipment.
- The drawing must be fluid, that is to say, the deformation of the material must be carried out continuously. The lack of fluid drawing can cause two problems; firstly, the material may not be deformed correctly and quality defects may appear, and secondly, this may increase excessive wear between the die and blank surfaces.
Under these conditions, we proceed to obtain the gravity centre of the slide in each degree of cycle position using the classic formula of the calculation of the mass centre, see [[
In our case, we take the values of the tonnage as masses, which are applied to our physical system defined by the press. Therefore, we can obtain the equations defined below to determine the press imbalance.
We seek to obtain the imbalance in each press position during a cycle; therefore, we obtained the tonnage values of the four sensors are the same degree of press and we replaced them in the same equation. We performed this process in order to obtain the displacement in the plane
(
where
(
The vector encompassing the points of the gravity centre of the press in the plane
(
Figure 6 shows the values of the gravity centre in a 3D representation within limits that we will call a "pyramid", where the obtained information can be analysed. The values X and Y represent the position of the gravity centre, while the coordinate Z represents the tonnage value. In orange, we can see the limits set by the manufacturer regarding the recommended imbalance based on the force exerted by the press.
The lower the force, the greater the tolerance to imbalance, and the greater the force, the greater the damage that can produce a minimum imbalance and thus the lower the tolerance. The pyramid defines the maximum limits that the values of the gravity centre on the X and Y axes can reach for each pressing force, these values are represented on the Z axis. In the example shown in Figure 6, the range of forces is from 200 to 2500 tonnes. In summary, what we have is a maximum deviation limit of the gravity centre defined on the X and Y axes for each force value, superimposing each of the planes obtained for a value of the force on the Z axis up to 2500 tonnes. We thus obtain the pyramid shown in the image. Within this area is where we plot the values of the gravity centre obtained.
Tests were carried out to verify that our system actually detected minimal variations in stamping, ensuring its sensitivity and its ability to warn us of any anomalies. Tests were carried out by forcing an imbalance in the stamping with different heights up to 1 mm in one of the four zones of the connecting rod feet. These height differences were defined in various configurations and the system was tested in 16 different slope combinations, forcing the slope knowing the desired curve of the gravity centre to be obtained.
In Figure 7, we can see the set up of the equipment used to carry out the test, where after calibration of the system to ensure that it was perfectly balanced, 1 and 2 mm thick steel plates were placed in various configurations on each of the pillars of the press, forcing the unevenness towards one of the sides of the slide. In Figure 7, a test configuration is shown with the imbalance intentionally forced to the right side of the slide.
In this case, two plates of 1 mm were placed in the pillars on the right, where we expected to see a deviation in the value of the centre of gravity to the right on the X axis and values centred on the Y axis. The result obtained was as expected, as we can see in Figure 8. With all the combinations studied in the test obtaining a result as expected, it can be said that the system worked correctly [[
This system, called a GC-WatchdogAlarm, monitors the condition of the press stamping and warns us when a pattern appears that we consider outside the correct working standards. To this end, two restrictions have been defined that must not be complied with: one is that there should be no deviation in the stamping and the second is that there should be no difference between each of the force values for each press position greater than usual.
The GC-WatchdogAlarm tool runs every 24 h, analysing all the stamping parts made during a day of production. In the case of finding an anomaly, it generates an alarm that is sent to the maintenance team in order to perform a deep analysis of what happened. This is a good tool to take advantage of when making decisions. Below, we explain each of the restrictions in more detail.
In order to know when the press begins to work with an anomalous behaviour, safety limits have been defined within the pyramid of the press that indicate the degree of malfunction. They have been classified as follows: "under surveillance" behaviour, when it exceeds the defined limit in green; "warning" behaviour, when it exceeds the yellow line; and "urgent revision" behaviour, when values outside the red limit occur. The limit values are calculated as 33% and 66% of the limit value established by the manufacturer. These limits can be seen in the following Figure 9.
As long as the GC value remains within the green zone, this will be considered normal and the alarm sending system will not perform any action after the analysis. When the first limit is exceeded, an alarm is generated to monitor the behaviour of the press. At this point, it is determined whether it is a random anomaly that will not happen again or a repetitive event of strokes outside the normal work area. If this happens, then the person in charge will be notified so that the necessary measures can be taken. When there are values that exceed the yellow limit, the procedure to be followed is the same as just explained, but this time, a thorough inspection of the different elements involved in the stamping process is directly carried out, making the necessary adjustments to return to the normal work situation. Furthermore, finally, if the limit defined in red is exceeded, production must be stopped urgently.
As we have already said, to obtain a good conformation of the piece, the deep drawing process must be continuous, so that the steel sheet slides into the die in a fluid way. The geometry of the design of many parts, together with the thicknesses of the sheets with which we work, need to meet these requirements. Failure to follow these conditions could lead to the occurrence of unfavourable events such as excess friction and wear of the die surface. In addition, the stretching of the material would not be adequate and cracks could appear. Industrial presses are designed to control the speed of the press, where the speed of raising and lowering of the die is higher than that at the time of drawing. In the following Figure 10, one can see the variation in the speed of the press in the degrees that the drawing is carried out, approximately between 100 and 180 degrees.
To detect possible anomalies in this continuous deformation, use of the DBSCAN [[
There are very efficient methods to choose the most optimal value of the parameter
The value of the minimum number of points,
It should be noted that unlike the centred stamping analysis that is performed for all dies equally, in this case, DBSCAN will be applied differently to each of the dies used in the press. This is due to the geometry that each piece has, where the resulting force obtained will have a different behaviour depending on the drawing distance, some areas with greater depth than others or the adjustment of the die limits, among others. For these reasons, the value of
; /* Initialise epsilon value */ []; /* Initialise empty array */
DBSCAN was adapted and the distances were taken between points in three dimensions to obtain the number of clusters. However, if we want to obtain the epsilon of the record, and subsequently apply the algorithmic DBSCAN, this will result in a very high computational cost. To reduce the calculation time, the alternative was obtaining the number of clusters in each cycle twice in 2D, one for the data in the
Once the proposed method was tested and it was verified that it works correctly, it was put into production. The
The first identified case shown in Figure 11 was detected with the die of the roof of a Ford Transit van, where the alarm system informed us that the value of the tonnage was around 2300 Tm, while the theoretical value defined for this item should be around 1760 Tm. The tonnage was above the safety limit value of the top of the pyramid, 2000 Tm. In addition, it far exceeded the theoretical value defined in the design phase, which led to excess effort of the press and the problems that this entails. After finding out the root of the problem, tests were carried out with the equipment to reduce the press effort without affecting the quality of the part. Finally, the working parameters of the press were adjusted. In this case, the slide adjustment was modified and the tonnage was reduced by up to 700 tons, therefore leaving the press working at 1600 Tm without affecting the quality of the part and working even below the design value obtained from the simulation.
The second found case shown in Figure 12 had the same pathologies as explained in anomaly 1. The body side part of the Galaxy was being manufactured at around 2400 tons, while the theoretical tonnage value obtained from the simulation was specified at 1639 Tm. After completing different tests, the force of the press was reduced without affecting the quality of the part. This was solved by modifying the adjustment of the slide in order to reduce the tonnage to the theoretical values defined in the design phase. In the two cases explained, it was concluded that the problem appeared due to a bad configuration of the work parameters of the press.
The last case of an anomaly detected in the press was due to an alarm sent through the GC-WatchdogAlarm system using the DBSCAN algorithm that identified an item that was working without the desired continuity in the drawing and giving a result of two identified clusters, as clearly seen in Figure 13. In this case, the problem was the outer door panel part of a Ford S-Max. The maintenance workers, when they went to check the press, found that it emitted unusual sounds and found stronger vibrations than usual in the concrete structure on which the press was mounted. This did not happen continuously but occurred at certain random stamping strokes. The workers decided to use the web application to consult the stored history of the work parameters and analyse it to obtain new information that could help to understand what was happening, since on previous occasions revisions had been made during the manufacture of this part without finding any anomaly in the press. The data were analysed in the web application and it was verified that the stored tonnage curves did not have the usual behaviour, since during drawing, the value of the tonnage should gradually increase, but in this case it had not happened. In the image shown below, we have a normal tonnage value on the left and the die curve of the S-Max outer door panels on the right.
In the bottom curve, marked in green we can see how the tonnage gradually increases during deep drawing. We can say that continuous drawing is being carried out; this being the right process during the stamping of a part. The opposite happens with the part that is presenting problems during manufacture, since we can observe discontinuity during drawing, which indicates that something is not working properly.
After a thorough analysis of the configuration of the press, it was found that the punch of the die was slightly higher than the blank holder, and this prevented drawing from being fluid. For this reason, one could feel the strokes that transmitted great vibrations to the entire press. After modifying the cushion configuration to change the blankholder and punch height, the problem was solved and excessive vibrations were avoided. In Figure 14, you can see the gap between the values of the centre of gravity within the pyramid.
To summarise, we show the results obtained in Table 2, where we can see the amount of effort reduced thanks to the methodology presented in this paper.
In the first two anomalies, the value of the effort made by the press was greatly reduced. In the manufacture of the roof part of the vehicle, we have reduced the tonnage from 2300 to 1600 Tm, reducing it by about 700 Tm. We have done the same in the manufacturing part of the side part of the body, where the tonnage was reduced by 800 Tm. Considering the press as an elastic element that can be deformed, we can confirm that the force was reduced both at the structural level and in the different mechanical elements. This allows us to extend the useful life of the equipment and avoid unexpected breakdowns in the short term. In addition, the energy consumption was reduced, since the effort made is lower. In the third anomaly detected, where two clusters were found in the data of the calculated gravity centre, we can confirm that the wear was reduced both on the die surface and on the blank surface. In addition, we reduced the vibrations at the structural level that can be harmful to the press.
The use of existing data to develop a new application is an important concept for the development of Industry 4.0. Many companies and research teams develop their algorithms and ideas from the installation of new sensors without taking into account the implications that these proposals have in real factories. The cost of the sensor, installation setup, maintenance, machine modifications and replicating this for hundreds of machines causes many of the ideas to fail when the innovation is implemented in industry. Therefore, in this article, and in previous work of the group [[
Graph: Figure 1 Kinematic chain breakdown of a mechanical press.
Graph: Figure 2 Single-action mechanical press sketch.
Graph: Figure 3 Tonnage data of a press cycle.
Graph: Figure 4 Press position vs. slide distance to BDC. Detailed Y axis information is not shown due to confidentiality.
Graph: Figure 5 Sketch of the press slide top view with the four connecting rod feet positions. A,B are slide measurements. And a,b are distance between rod feet.
Graph: Figure 6 Gravity centre data of a stamping cycle.
Graph: Figure 7 Set up equipment with an imbalance of 1 mm on the right side of the press.
Graph: Figure 8 Imbalance test results obtained with the GC tool. Red and green lines are press working limits. Blue lines are gravity center measurements.
Graph: Figure 9 Gravity centre safety limits.
Graph: Figure 10 Press velocity during a cycle.
Graph: Figure 11 Roof part. Tonnage values exceeding top working limits.
Graph: Figure 12 Body side part. Tonnage values exceeding top working limits.
Graph: Figure 13 Outer door panels. Abnormal tonnage value (top). Correct tonnage value (bottom). Green circle indicates load during deep drawing.
Graph: Figure 14 Outer door panels. Gravity centre alarm without continuity. Red circle indicates discontinuity during deep drawing.
Table 1 Monitored variables in a stamping press.
Process Value Sensor Quantity Units Criterion Tonnage Force 4 Tm 360 Cylinder cushion pressure 8 bar 360 Cylinder cushion pressure 2 mm 360 Counterbalance pressure 1 bar 360 Overload pressure 2 bar 360 Energy consumption 1 W/h 360 Clutch activation time 1 ms Mini-Term Brake activation time 1 ms Mini-Term Slide position 1 mm Mini-Term Press speed 1 hit/min Mini-Term Die clamp travelling time 12 ms Mini-Term Lubrication mapping 1 l/s -
Table 2 Results of parts identified as anomalies.
Car Part Prev. Tonnage Post Tonnage Clusters Safety Issue Roof 2327 1618 1 Exceed warning limit Body side 2415 1625 1 Exceed warning limit Outer door panels 1720 1720 2 Continuity
Conceptualisation, I.P.-A.; methodology, I.P.-A.; validation, I.P.-A. and N.M.; formal analysis, I.P.-A.; investigation, I.P.-A., N.M. and E.G.; resources, E.G.; data curation, I.P.-A.; writing—original draft, I.P.-A. and N.M.; writing—review and editing, I.P.-A., N.M. and E.G.; project administration, N.M. and E.G.; funding acquisition, N.M. and E.G. All authors have read and agreed to the published version of the manuscript.
Not applicable.
Not applicable.
Not applicable.
The authors declare no conflict of interest.
The authors gratefully acknowledge the support by the Universidad CEU Cardenal Herrera, Ford Spain S.L. and Fundación para el Desarrollo y la Investigación (FDI), Spain.
By Ivan Peinado-Asensi; Nicolás Montés and Eduardo García
Reported by Author; Author; Author