Probing the adsorption of polymer depressants on hydrophobic surfaces using the quartz crystal microbalance

The hydrophobicity of a surface is an important property in many areas of science and engineering. This is especially the case in mineral processing, where differences in surface hydrophobicity lie at the heart of the separation process of flotation. Chemicals are used to increase and decrease the natural hydrophobicity of minerals to attain a better separation between valuable and worthless material. Polymers are often used to reduce mineral surface hydrophobicity. Decades of empirically based decision making have produced a list of effective depressants. However the detailed study of how these polymer depressants affect surface hydrophobicity and mineral recovery lags behind applied investigations. The aim of this thesis was to study the adsorption of commonly used depressants on model surfaces and to interrogate the action of these polymers in reducing surface hydrophobicity. We have modelled the degree of hydrophobicity of common minerals in order to study polymer depressants with methods not commonly used in studies of surface characterisation in flotation. The model surfaces (self-assembled monolayers, SAMs) allowed us to use the quartz crystal microbalance with dissipation monitoring (QCM-D) to study the adsorption of polymers. The QCM-D can be used to obtain adsorption isotherms, adsorption kinetics, water content of adsorbed layers, and information on the conformation of the adsorbed polymer. The results from the QCM-D were correlated with the contact angle data from the captive bubble measurements, with which we assessed the hydrophobicity of the surface before and after polymer adsorption. Three of the polymers layers were probed with dynamic dewetting studies, in order to test other modes of depressant action. Three types of polymers were studied - a polyacrylamide (Polymer-H), a polyelectrolyte CMC (carboxymethyl cellulose) and a group of dextrins (Dextrin-TY, a phenyl succinate substituted dextrin (PS Dextrin) and a styrene oxide substituted dextrin (SO Dextrin)). These polymers are commonly used or have potential to be used in the depression of talc and graphite. Polymer-H was used to investigate the hydrophobic bonding between a non-ionic polymer depressant and chemically inert and non charged surfaces by probing the influence of substrate hydrophobicity on polymer adsorption and reduction of contact angle. Three different model surfaces were used (mixed self-assembled 0.5 SAM, 0.7 SAM or single self-assembled 1.0 SAM monolayers) with advancing contact angles between 75?? and 119??. The study of Polymer-H found that the substrate hydrophobicity is an important factor in adsorption of this polymer and the change in contact angle upon adsorption depends on adsorbed amount. The effectiveness of Polymer-H to reduce surface hydrophobicity was established to correlate with its conformation and morphology. CMC was investigated to find out how a stimulus responsive polymer depressant can be used in flotation. It was established that the adsorbed amount and rate of adsorption of CMC increase with decreasing of pH or increasing of ionic strength. It was shown that the surface hydrophobicity of a CMC pre-adsorbed layer changes with the environment and these alterations are fully reversible. A switch of ionic strength (from 10-2 M KCl to 10-1 M KCl) caused partial dehydration of the adsorbed layer and a decrease of the receding contact angle by 20??. A pH switch (pH = 9 to pH = 3) resulted in a 40?? change in receding contact angle. The CMC investigation showed that the use of a stimulus responsive polymer presents opportunities for exploiting solution conditions as a means to effect a better mineral separation in flotation The adsorption of three dextrin-based polymers on a model hydrophobic surface has been characterized using the quartz crystal microbalance with dissipation monitoring (QCM-D). The three polymers (one standard dextrin and two dextrins with different aromatic group substitutions) exhibited varying affinities and capacity for adsorption on the hydrophobic substrate. The effect of the three polymers on the static contact angle of the surface was studied using captive bubble contact angle measurements. The three polymers were seen to reduce the receding contact angle by similar amounts (approximately 14 degrees) in spite of having varying adsorbed amounts and differences in adsorbed layer water content. Although no differences were observed in the ability of the polymers to reduce the static contact angle, measurements of the dewetting dynamics between a rising air bubble and the polymer covered substrate yielded stark differences between the polymers, with one polymer slowing the dewetting dynamics by an order of magnitude more than the other two polymers. The differences in dewetting behaviour correlate with the adsorbed layer characteristics determined by QCM-D.

Thesis (PhD)--University of South Australia, 2010